iTP Light C7, C8, C9 instruction
Thank you for purchasing iTP Light C series flashlight, please read the manual carefully before using, this instruction is applicable
to items C7, C8 and C9.
Product Compose
The package includes below product and accessories: one flashlight, one manual, one warranty card, two spare O-rings,
one rubber boot.
Please contact with the local distributor if there is something damaged or missed.
Features:
1. Sizes: C7 length 105.5mm, Diameter 27mm, Weight 80g (Excluding battery)
C8 length 155mm, Diameter 27mm, Weight 100g (Excluding battery)
C9 length 90mm, Diameter 27mm, Weight 65g (Excluding battery)
2. LED type: Cree 7090-XR-E Q5, life span up to 50000 hours
3. Hard finish with Type â…˘ anodization
4. Aluminium alloy reflector
5. Battery reverse-polarity protection: the circuit uses ideal diode technology, high credibility.
6. Digital infinite beam adjusting function, you can select any level from 6lumens to 190lumens and lockout present memory.
7. Strobe and SOS function, (excluding tactical version)
8. Use Boost-Buck automatically drive circuit, working voltage from 1.0V to 4.2V
9. Battery compatible
C7 is compatible for 1XAA, NI-HI battery and 14500 lithium cell
C8 is compatible for 2XAA, NI-HI battery
C9 is compatible for 1XCR123A and 1X16340 lithium cell
10. Constant current output control system, and no blink at the lowest illumination level
Operation
1. Battery installation, twist the head or tail switch to install battery. (Positive polarity direct to the head)
2. Tighten the light, press the tail switch or rotate the head into multifunctional operation.
3. Functions and operation
Function transforming: Illumination-Strobe-SOS
a. Lumination function
1)Press the tail switch into lumination status, rotate light head (about 1/4 circle) to turn into the beam adjustment status,
light will be fluctuating gradually much brighter or much dimmer.
2)Tighten the head to memorize any brightness level you favorable.
3)If you would like the ramp to change in reversed direction, please tighten the light firstly then loose it again.
4)Every start will enter into default mode (lumination function).
5)Two flashing mention for the brightness reaching on highest or lowest level.
b. Strobe function: press tail cap switch into lumination status, press gently again or click twice (within 2 seconds) to
enter into strobe status.
c. SOS function: gently press tail cap switch twice sequential go to SOS function under the lumination status,
and press once only under strobe status.
4.Cut off power above 2 seconds will enter into another start.
Remark:
1.Models C7, C8 and C9 use the same head, you can replace the body freely.
2.Tactical version does not support Strobe and SOS functions, same feature for digital infinite beam adjusting function.
3. When the voltage lower than 0.8V,the circuit may run abnormally, please replace the battery in time.
Warranty
ITP warrants its products to be free from defects in materials and workmanship.
Within 30 days of receipt, any defective lights will be repaired or replaced by ITP or its dealers & distributors.
After the initial 30 days iTPTM will repair or replace, at its option and without charge, any product or part which is found to be defective under normal use and service within 18 months starting from the date of purchase.
After 18 months from the purchase date, ITP will still provide warranty service; labor is free but the cost of any parts required may be charged.
Such repair or replacement as described above shall be the purchasers’ sole and exclusive remedy under this warranty. This warranty does not cover normal maintenance and service and does not apply to any products or parts which have been subject to modification, misuse, negligence, accident, improper maintenance or repair by anyone other than ITP or its duly appointed representatives.
Any shipping or related costs incurred in the course of any warranty claim are the sole responsibility of the purchaser.
|